消力池出池水流對橋墩的影響
發布時間：2018-11-26 15:15
【摘要】：本文利用流體計算軟件fluent提供的RNG K-ε紊流模型,采用Vof法追蹤自由水面,以某水庫工程的消力池為基礎,采用1：100的模型比尺縮放,通過數值仿真得到了相應工程的計算結果,如池內流態,臨底流速,底板動水壓強,以及橋墩處的壓強和流速等。 本文的研究重點是如何減小消力池出池水流對水庫下游公路橋墩的影響,為此筆者提出了消力池體型的優化設計方案。采用數值仿真的方法,分析所得結果(出池水流對橋墩的作用等)是否符合工程的實際要求。從本工程的實際情況以及一些學者的研究成果來看,優化消力池的體型,必須從三個方面著手：一、控制消力池的底板壓力在一定范圍內(p120pa)二、控制消力池水流的臨底流速在一定范圍內(v0.6m/s)三、控制橋墩所在位置的壓強和流速在一定范圍內(p100pa, v0.4m/s),以保證在減小消力池出池水流對橋墩影響的情況下,對消力池本身不造成過大的破壞。因此下文將從這三個方面,系統的分析優化消力池體型后的計算結果是否符合工程的實際要求。 本文采用二維計算模型,計算取的是從溢洪道的消力池直至下游河水中的無限長的水域,本次計算長度設定為67cm,其中消力池寬度是l0cm,取消力池縱剖面的軸線進行研究。分別計算不同的消力池體型,水流在橋墩上游位置的流態、壓強及流速的變化等。然后不斷的優化消力池的體型,看能否達到工程的實際要求。選擇100年一遇的流量下的工況計算并優化,因為100年一遇的流量對工程結構的破壞有一定的警示意義。 通過計算和分析,得出優化的體型能夠保證水流對消力池底板的壓力和臨底流速在可承受范圍內,不至于破壞底板。在一定程度上能減少對下游河道高速公路橋墩及公路的影響,但仍會對橋墩造成一定的破壞。因此,建議在工程實踐中采用三角導流板分流,降低水流對公路橋墩的作用。
[Abstract]:In this paper, the RNG K- 蔚 turbulence model provided by the fluid calculation software fluent is used to track the free water surface by using the Vof method. Based on the stilling pool of a reservoir project, the scale of the model is 1: 100. Through numerical simulation, the corresponding engineering results are obtained, such as the flow state in the pool, the near bottom velocity, the hydrodynamic pressure of the bottom plate, and the pressure and velocity at the pier, etc. The emphasis of this paper is on how to reduce the influence of the outlet flow of the stilling pool on the bridge piers downstream of the reservoir. Therefore, the author puts forward the optimal design scheme of the stilling pool shape. The numerical simulation method is used to analyze whether the results (the effect of the flow out of the pond on the pier etc.) meet the practical requirements of the project. From the actual situation of the project and the research results of some scholars, we must start from three aspects to optimize the shape of the stilling pool: first, to control the bottom pressure of the stilling pool within a certain range (p120pa) 2, The critical bottom velocity of the stilling pool is controlled within a certain range (v0.6m/s), and the pressure and velocity of the bridge pier are controlled within a certain range (p100pa, v0.4m/s). In order to ensure that the impact of the flow of the stilling pool on the pier is reduced, the stilling pool itself does not cause too much damage. Therefore, the following three aspects, the system analysis of the optimization of the stilling pool shape after the calculation results meet the actual requirements of the project. In this paper, a two-dimensional model is used to calculate the infinite length of water from the stilling pool of the spillway to the infinite length of the downstream river. The calculated length is set at 67 cm, in which the width of the stilling pool is 10 cm. The axial line of the longitudinal section of the spillway is cancelled. Different types of stilling pool, flow pattern of flow upstream of pier, variation of pressure and velocity are calculated respectively. Then continuously optimize the shape of the stilling pool to see if it can meet the actual requirements of the project. The operating conditions under the flow rate of 100 years are selected and optimized, because the flow rate once in 100 years has a certain warning significance to the damage of the engineering structure. Through calculation and analysis, it is concluded that the optimized shape can ensure that the pressure and the flow velocity of the bottom plate of the stilling pool are within the tolerable range, so that the bottom plate will not be damaged. To some extent, it can reduce the influence on the pier and highway of the downstream river highway, but it will still cause some damage to the pier. Therefore, it is suggested that triangular diversion plate should be used in engineering practice to reduce the effect of water flow on highway piers.
【學位授予單位】：昆明理工大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TV135.2;U442.3
本文編號：2358917
[Abstract]:In this paper, the RNG K- 蔚 turbulence model provided by the fluid calculation software fluent is used to track the free water surface by using the Vof method. Based on the stilling pool of a reservoir project, the scale of the model is 1: 100. Through numerical simulation, the corresponding engineering results are obtained, such as the flow state in the pool, the near bottom velocity, the hydrodynamic pressure of the bottom plate, and the pressure and velocity at the pier, etc. The emphasis of this paper is on how to reduce the influence of the outlet flow of the stilling pool on the bridge piers downstream of the reservoir. Therefore, the author puts forward the optimal design scheme of the stilling pool shape. The numerical simulation method is used to analyze whether the results (the effect of the flow out of the pond on the pier etc.) meet the practical requirements of the project. From the actual situation of the project and the research results of some scholars, we must start from three aspects to optimize the shape of the stilling pool: first, to control the bottom pressure of the stilling pool within a certain range (p120pa) 2, The critical bottom velocity of the stilling pool is controlled within a certain range (v0.6m/s), and the pressure and velocity of the bridge pier are controlled within a certain range (p100pa, v0.4m/s). In order to ensure that the impact of the flow of the stilling pool on the pier is reduced, the stilling pool itself does not cause too much damage. Therefore, the following three aspects, the system analysis of the optimization of the stilling pool shape after the calculation results meet the actual requirements of the project. In this paper, a two-dimensional model is used to calculate the infinite length of water from the stilling pool of the spillway to the infinite length of the downstream river. The calculated length is set at 67 cm, in which the width of the stilling pool is 10 cm. The axial line of the longitudinal section of the spillway is cancelled. Different types of stilling pool, flow pattern of flow upstream of pier, variation of pressure and velocity are calculated respectively. Then continuously optimize the shape of the stilling pool to see if it can meet the actual requirements of the project. The operating conditions under the flow rate of 100 years are selected and optimized, because the flow rate once in 100 years has a certain warning significance to the damage of the engineering structure. Through calculation and analysis, it is concluded that the optimized shape can ensure that the pressure and the flow velocity of the bottom plate of the stilling pool are within the tolerable range, so that the bottom plate will not be damaged. To some extent, it can reduce the influence on the pier and highway of the downstream river highway, but it will still cause some damage to the pier. Therefore, it is suggested that triangular diversion plate should be used in engineering practice to reduce the effect of water flow on highway piers.
【學位授予單位】：昆明理工大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TV135.2;U442.3
【參考文獻】
相關期刊論文 前10條
1 李永業;孫西歡;李飛;束德方;;管道消能研究概述[J];電力學報;2010年02期
2 田景環;翟雯航;;高拱壩下游消能防沖方案選擇的數值方法[J];廣東水利水電;2005年06期
3 王智娟;岳漢生;姜伯樂;;跌坎式底流消力池水力特性三維數值模擬與試驗研究[J];長江科學院院報;2013年08期
4 魏林堅;;江口水電站樞紐布置設計[J];甘肅水利水電技術;2006年02期
5 謝波;曲景學;胡靜;王橋;;龍開口水電站挑坎體型優化試驗研究[J];吉林水利;2009年01期
6 朱雅琴,張法星,許唯臨;舌形挑流鼻坎水力特性研究[J];科學技術與工程;2004年05期
7 劉沛清;冬俊瑞;;自由面流的速度分布理論分析[J];水利水運科學研究;1993年03期
8 劉沛清，，冬俊瑞;消力池及輔助消能工設計的探討[J];水利學報;1996年06期
9 李敏;;柏葉口水庫壩型方案比選[J];山西水利;2007年04期
10 許曉會;;咸陽市供水工程輸水管道設計方案分析與優化[J];陜西水利水電技術;2007年02期
本文編號：2358917
本文鏈接：http://www.lk138.cn/kejilunwen/jiaotonggongchenglunwen/2358917.html
