發布時間：2019-05-23 19:34

【摘要】：本文采用TIG-MIG復合焊對AZ31鎂合金型材進行了焊接研究,主要研究了焊縫成形、微觀組織、力學性能。首先,進行了 TIG-MIG復合焊系統搭建,主要包括兩個部分:兩焊槍的夾持裝置設計和控制系統設計。其次是兩焊槍的相對位置關系的確定。適合本次試驗的兩焊槍的位置關系是:兩焊槍在同一直線上,TIG焊槍在前,MIG焊槍在后,TIG焊槍垂直與工件,MIG焊槍與TIG焊槍成45°夾角。然后研究了工藝參數(TIG焊電流、MIG焊電流、MIG焊電壓、焊接速度、TIG焊電弧與MIG焊電弧的中心距離)對焊縫成形的影響規律,最終獲得成形良好的接頭。對成形良好的焊接接頭進行了拉伸試驗,得出抗拉強度達到215MPa,約為母材的79.63%,接頭的斷裂形貌主要呈現為韌窩斷裂與解理斷裂的混合型斷裂。對焊接接頭進行了硬度試驗,得出焊縫硬度的平均值為57.78HV、熱影響區硬度的平均值為52.81HV、母材硬度的平均值為56.14HV。對焊接接頭進行了微觀組織研究,研究結果表明焊接接頭由母材區、熱影響區、焊縫區組成。母材的微觀組織為較均勻,晶粒細小,主要由α-Mg相組成。熱影響區的微觀組織呈現晶粒粗大而又不規則,有少量的β-Mg17Al12金屬間化合物。焊縫為細小均勻的等軸晶,主要由α-Mg相和β-Mg17Al12金屬間化合物兩個部分組成。β-Mg17Al12金屬間化合物主要分布在晶粒和晶界上,呈現條狀和粒狀。最后對比分析了 TIG-MIG復合焊高速焊與低速焊的接頭宏觀、微觀、硬度。從宏觀上比較,高速焊接的焊縫表面魚鱗紋更細和熔寬更寬。從微觀上比較,高速焊接的熱影響區與焊縫晶粒比低速焊接的相應區域更細小。從接頭硬度比較,高速焊接的熱影響區硬度和焊縫硬度比低速焊接的相應區域大。
[Abstract]:In this paper, TIG-MIG composite welding was used to study the welding of AZ31 magnesium alloy profiles. The weld forming, microstructure and mechanical properties were mainly studied. Firstly, the TIG-MIG composite welding system is built, which mainly includes two parts: the clamping device design and the control system design of the two welding guns. Secondly, the relative position relationship of the two welding guns is determined. The position relationship between the two welding guns is as follows: the two welding guns are in the same straight line, the TIG welding torch is in front of the MIG welding torch, the TIG welding torch is perpendicular to the workpiece, and the MIG welding torch is 45 擄angle with the TIG welding torch. Then the influence of process parameters (TIG welding current, MIG welding voltage, welding speed, center distance between TIG welding arc and MIG welding arc) on weld forming is studied, and finally the well formed joint is obtained. The tensile test of the well-formed welded joint shows that the tensile strength is 215 MPA, which is about 79.63% of that of the base metal, and the fracture morphology of the joint is mainly the mixed fracture of dimple fracture and cleavage fracture. The average hardness of the welded joint is 57.78 HV. the average hardness of the heat affected zone is 52.81 HV. the average hardness of the base metal is 56.14 HV. the average hardness of the welded joint is 57.78 HV. the average hardness of the heat affected zone is 52.81 HV. the average hardness of the base metal is 56.14 HV. The microstructure of the welded joint is studied. The results show that the welded joint is composed of base metal zone, heat affected zone and weld zone. The microstructure of the base metal is uniform and the grain size is fine, which is mainly composed of 偽-Mg phase. The microstructure of the heat affected zone is coarse and irregular, and there are a small amount of 尾-Mg17Al12 intermetallic compounds. The weld is a fine and uniform equiaxed crystal, which is mainly composed of 偽-Mg phase and 尾-Mg17Al12 intermetallic compound. 尾-Mg17Al12 intermetallic compound is mainly distributed on grain and grain boundary, showing strip and grain shape. Finally, the macro, micro and hardness of high speed welding and low speed welding of TIG-MIG composite welding are compared and analyzed. From a macro point of view, the fish scale lines on the weld surface of high speed welding are thinner and wider. Compared with the corresponding area of low speed welding, the heat affected zone and grain size of high speed welding are smaller than those of low speed welding. Compared with the hardness of the joint, the hardness of the heat affected zone and the hardness of the weld in the high speed welding are larger than those in the low speed welding.
【學位授予單位】：西南交通大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TG456

【參考文獻】

相關期刊論文 前10條

1 李娜;馬志華;陳東高;馮勝強;郭海林;;AZ31鎂合金激光-MIG復合焊接接頭組織和疲勞性能研究[J];熱加工工藝;2016年07期

2 平奇文;馬國紅;胡小武;葉佳;;AZ31B鎂合金TIG-MIG雙弧焊接組織分析[J];熱加工工藝;2015年03期

3 溫彤;劉詩堯;陳世;劉瀾濤;楊臣;;高頻振動對AZ31鎂合金TIG焊接接頭微觀組織與力學性能的影響（英文）[J];Transactions of Nonferrous Metals Society of China;2015年02期

4 游國強;杜娟;陳磊;王向杰;;壓鑄AZ91D鎂合金TIG焊接氣孔研究[J];材料工程;2014年12期

5 森 久史;蔡千華;;鎂合金在車輛結構部件上的應用[J];國外鐵道車輛;2014年06期

6 劉冬花;聶軍;馬國紅;;鎂合金雙弧焊接過程研究與分析[J];南昌大學學報(工科版);2014年02期

7 蘇允海;林金梁;蔣煥文;劉政軍;;磁場下鎂合金A-TIG接頭成形性及顯微組織分析[J];焊接學報;2013年11期

8 張兆棟;劉黎明;宋剛;;AZ31B鎂合金直流脈沖MIG焊接特性(英文)[J];Transactions of Nonferrous Metals Society of China;2013年02期

9 趙菲;吳志生;高珊;何佳斌;趙兵;陳智偉;;AZ31鎂合金MIG焊接頭深冷處理及其微觀組織[J];現代焊接;2012年09期

10 楊濤;張生虎;高洪明;吳林;許可望;劉永貞;;TIG-MIG復合焊電弧特性機理分析[J];焊接學報;2012年07期

相關博士學位論文 前1條

1 劉德佳;攪拌摩擦焊接鎂合金微區織構、力學性能與斷裂機制[D];重慶大學;2014年

相關碩士學位論文 前2條

1 婁小飛;TIG-MIG復合焊電弧形態及熔滴過渡行為研究[D];山東大學;2014年

2 曹全金;鎂合金活性MIG焊接研究[D];大連理工大學;2012年

，

本文編號：2484167