【摘要】：焊接是奧氏體不銹鋼板及型材的重要加工手段。高氮奧氏體不銹鋼是用氮部分或完全取代鎳以獲得單相奧氏體組織的一類鋼,可節約大量鎳,降低成本,且具有優良的力學性能和耐腐蝕性能,因此獲得了廣泛的應用。但研究表明,高氮奧氏體不銹鋼在焊接過程中可能會出現氮的損失、氮化物析出等問題,對接頭的力學性能有不利影響。因此,對高氮奧氏體不銹鋼焊接性能的研究具有實際意義。本論文使用Gleeble-3500型熱/力模擬試驗機對固溶處理后的一種新型高氮高錳低鎳奧氏體不銹鋼分別進行了峰值溫度為1050℃~1300℃、線能量為5~12kJ/cm條件下的焊接熱影響區(HAZ)模擬實驗,并根據熱模擬實驗結果進行實際焊接;采用金相顯微鏡對模擬HAZ顯微組織和焊接接頭進行了分析,結合使用X射線.衍射、掃描電鏡和透射電鏡對模擬焊接HAZ顯微組織進一步分析,并對熱模擬實驗鋼和焊接接頭進行拉伸、沖擊和硬度測試,研究實驗鋼模擬焊接HAZ和實際焊接接頭的力學性能。研究結果表明:不同峰值溫度的熱模擬實驗后,實驗鋼晶粒隨峰值溫度的升高逐漸變大;抗拉強度、硬度隨峰值溫度升高逐漸降低,但均分別高于母材799MPa的抗拉強度及其硬度239.26HV;塑性略微低于母材,峰值溫度對其影響不大;但在峰值溫度為1150℃處呈現不一樣的變化規律。實驗鋼在經歷不同線能量的焊接熱循環后,焊接HAZ組織主要為奧氏體和孿晶,晶粒中有(Cr,Mn,Fe)23C6析出,隨著線能量的增加,此碳化物析出逐漸消失,晶粒也發生不同程度的長大;實驗鋼的塑性略低于母材,但線能量的變化對其塑性影響不大;實驗鋼硬度均高于母材,不存在軟化區域;線能量為10kJ/cm時,實驗鋼具有最佳的力學性能,抗拉強度達到826MPa,延伸率54.6%,吸收功306.1J,硬度為319.03HV。采用優化后的試驗參數對實驗鋼進行了TIG焊,焊接接頭熱影響區組織均勻,硬度高于母材,拉伸斷口出現在焊縫上。
[Abstract]:Welding is an important means of processing austenitic stainless steel plates and profiles. High nitrogen austenitic stainless steel is a kind of steel which uses nitrogen partly or completely to replace nickel to obtain single-phase austenitic structure. It can save a lot of nickel, reduce cost, and has excellent mechanical properties and corrosion resistance, so it has been widely used. However, the study shows that the loss of nitrogen and the precipitation of nitride may occur in the welding process of high nitrogen austenitic stainless steel, which has a negative effect on the mechanical properties of the joints. Therefore, it is of practical significance to study the welding properties of high nitrogen austenitic stainless steel. In this paper, a new type of high nitrogen, high manganese and low nickel austenitic stainless steel after solid solution treatment was studied by using Gleeble-3500 thermal / mechanical simulator. The peak temperature of the austenitic stainless steel was 1050 鈩，

本文編號：2401548