本文選題：修井作業 + 大斜度井��； 參考：《西南石油大學》2016年碩士論文

【摘要】：隨著大斜度井工藝在油田的大量應用,大斜度井的修井工況也越來越復雜。其井斜角大,水平位移長的特點,使得修井作業過程中管柱的軸力和扭矩在井筒中的傳遞困難。同時,由于修井管柱的直徑小、剛度低,增加了大修作業的風險。正確認識大斜度井修井管柱在井筒中的受力對提高修井效率、保障修井安全、降低修井成本至關重要。本文在前人研究的基礎上,針對大修井作業管柱力學認識相對薄弱的問題從實驗和模擬兩方面進行了研究。結合室內臺架實驗對修井工具作業過程中的鉆壓與扭矩模型進行了研究,建立了大斜度井大修作業全井管柱與套管(或井壁)的有限元仿真模型,并進行了現場實驗驗證；根據建立的有限元模型,研究了大斜度井大修作業參數敏感性問題；模擬了多種工況下的桿柱力學行為,對修井作業管柱組合及鉆壓范圍提出了指導意見。主要研究工作如下：(1)修井管柱力學行為模擬有限元建模方法研究：根據修井管柱與井壁之間的接觸特點,對管柱與井壁之間的接觸模型及接觸算法進行了研究；利用海洋波浪力學理論,對管柱在修井液中的粘滯阻尼模型進行了分析；結合室內臺架實驗,建立了修井作業過程中修井工具的鉆壓-扭矩模型；基于現場上提下放實驗,對有限元模型進行了驗證。(2)大斜度井修井作業參數敏感性分析：研究了起下鉆速度對管柱軸力的影響,結果表明起鉆速度增加,管柱承受的軸力也會隨之增大；分析了井斜角、造斜率、大鉤載荷等因素對管柱軸力和扭矩的影響,并通過百米軸力損失和百米扭矩損失對影響因素進行了量化分析；研究了摩擦系數、管柱壁厚及油套環空間隙對水平井管柱屈曲臨界載荷的影響,研究發現增大摩擦系數和減小環空間隙都會增大臨界屈曲載荷。(3)大斜度井修井作業工況力學行為模擬研究：分析了上提下放作業過程中,管柱的受力特點,得出了所分析的實鉆井管柱上提時接觸力要大于下放時接觸力,且第一增斜段百米軸力損失最大；對封隔器解封過程進行了研究,比較了大斜度井仿真鉤載、實驗鉤載及直井鉤載的關系：對套銑和磨銑作業進行了研究,提出了扶正器和鉆鋌的安放方案,并對臨界鉆壓進行了分析。在上述研究的基礎上,建立了一套大斜度井修井管柱力學有限元二次開發分析模塊,它有利于現場工程人員掌握修井管柱有限元分析方法,降低其使用門檻。本文的研究對大斜度井修井作業過程中的管柱組合確定、修井設備選擇及各技術參數優化提供了理論指導。
[Abstract]:With the application of large deviated well technology in oil field, the workover condition of large deviated well is becoming more and more complicated. Because of its large inclined angle and long horizontal displacement, it is difficult to transfer axial force and torque of pipe string in workover operation. At the same time, because the diameter of workover string is small and stiffness is low, the risk of overhauling operation is increased. It is very important to correctly understand the stress of workover string in wellbore to improve workover efficiency, ensure workover safety and reduce workover cost. On the basis of previous studies, this paper studies the problems of relatively weak understanding of pipe string mechanics in heavy workover operation from two aspects: experiment and simulation. The model of drilling pressure and torque during workover tool operation is studied with laboratory bench test. The finite element simulation model of pipe string and casing (or shaft wall) is established for heavy workover of large inclination well, and the field experiment is carried out to verify the model. According to the established finite element model, the sensitivity of heavy repair parameters of large deviated wells is studied, the mechanical behavior of rod string under various working conditions is simulated, and the guidance for tubing assembly and drilling pressure range of workover operation is put forward. The main research work is as follows: (1) finite element modeling method for simulating the mechanical behavior of workover string: according to the contact characteristics between workover string and shaft wall, the contact model and contact algorithm between pipe string and shaft wall are studied. Based on the theory of ocean wave mechanics, the viscous damping model of pipe string in workover fluid is analyzed, and the drilling pressure torque model of workover tool during workover operation is established in combination with the laboratory bench experiment. The sensitivity analysis of workover operation parameters of large inclination well is carried out by using finite element model. The influence of drilling speed on axial force of pipe string is studied. The results show that the axial force of pipe string increases with the increase of drilling speed, and the angle of well inclination is analyzed. The influence of factors such as slope making, big hook load on axial force and torque of pipe string is analyzed quantitatively through the loss of 100 meters axial force and 100 meter torque, and the friction coefficient is studied. The influence of string wall thickness and annular clearance on critical buckling load of horizontal well string, It is found that increasing the friction coefficient and decreasing the annulus clearance will increase the critical buckling load. It is concluded that the contact force when lifting the pipe string is greater than the contact force when it is lowered, and the maximum axial force loss of 100 meters in the first inclined section is obtained, and the Packer unsealing process is studied, and the simulated hook load of the large slope well is compared. The relationship between experimental hook load and hook-up load in straight well: the operation of sleeve milling and grinding milling was studied, and the arrangement scheme of centralizer and drill collar was put forward, and the critical drilling pressure was analyzed. On the basis of the above research, a set of finite element secondary development analysis module of workover string mechanics is established, which is helpful for field engineers to master the finite element analysis method of workover string and reduce the threshold of its use. The research in this paper provides theoretical guidance for the determination of tubing string combination selection of workover equipment and optimization of various technical parameters during workover operation in large deviated wells.
【學位授予單位】：西南石油大學
【學位級別】：碩士
【學位授予年份】：2016
【分類號】：TE935

【參考文獻】

相關期刊論文 前10條

1 談梅蘭;何小寶;王鑫偉;;井眼內鉆柱屈曲分析時端部約束方程的合理性[J];工程力學;2008年05期

2 朱炳坤;;水平狀態下鉆柱的屈曲分析[J];鉆采工藝;2008年02期

3 朱炳坤;;存在上凸彎曲的水平井眼中鉆柱的屈曲分析[J];石油鉆探技術;2008年01期

4 朱炳坤;鄧德鵬;;在水平井眼中存在下凹初彎曲鉆柱的屈曲分析[J];石油機械;2007年08期

5 劉峰;王鑫偉;;變曲率井中有重鉆柱屈曲的非線性有限元分析[J];機械科學與技術;2007年05期

6 劉峰;王鑫偉;甘立飛;;基于有限元分析的直井中鉆柱螺旋屈曲臨界載荷定義[J];工程力學;2007年01期

7 朱炳坤;;水平鉆柱屈曲載荷的分析計算[J];石油礦場機械;2006年04期

8 朱炳坤;;水平鉆柱的穩定性分析[J];鉆采工藝;2006年01期

9 朱炳坤;鄧德鵬;;用矩陣傳遞法分析水平鉆柱的穩定性[J];石油機械;2005年12期

10 劉峰,王鑫偉;水平井中鉆柱屈曲的非線性有限元分析[J];機械科學與技術;2005年08期

相關博士學位論文 前1條

1 劉峰;定向井中鉆柱非線性穩定性分析[D];南京航空航天大學;2005年

相關碩士學位論文 前1條

1 王盟圣;斜直井中考慮接頭影響的鉆柱穩定性分析[D];南京航空航天大學;2006年

，

本文編號：1885105