發布時間：2018-07-27 18:51

【摘要】：目前,國內大部分高壓流體遠程控制閥大多是采用手動控制,不利于自動控制及遠程控制；即使是自動控制閥,也多采用電磁力矩馬達作為驅動部分,其結構復雜、體積重量大、工作頻響低、沖擊大、響應速度慢、分辨率不高、控制精度低、抗干擾能力差,另外,在很多研究領域,都是需要微小流量來完成系統控制,以達到減小系統體積、重量、降低能耗損失以及提高系統性能的目的,但同時又必須承受高低壓及高低溫等特殊因素的影響。本文采用壓電陶瓷與金屬橡膠兩種材料來設計一種新型的精密流量閥。 本文主要研究了流量閥的流量特性、閥腔體內的流場分布特性和閥出口處的平紋波特性�；�于達西定律和流體質量守恒定理建立了閥流量特性的數學模型,采用matlab軟件分析了金屬橡膠幾何參數以及閥進出口壓差對閥流量特性的影響；采用Fluent12.0軟件仿真分析了圓角半徑、閥芯半錐角對其流場特性的影響,以及金屬橡膠參數對流量閥平紋波特性的影響規律。分析結果表明,該閥的流量特性不僅與驅動電壓有關,還與金屬橡膠環參數有關,圓角半徑以及閥芯半錐角對閥腔內流場的分布也有很大的影響,在閥進出口處安裝金屬橡膠環后,可使流出閥的流體速度變化平緩、方向趨于一致,流動更為平緩,一定程度上確保了閥輸出流量/壓力的穩定性,從而在一定的范圍內實現平紋波處理的功能。
[Abstract]:At present, most of the domestic high pressure fluid remote control valves mostly use manual control, which is not conducive to automatic control and remote control. Even the automatic control valve, electromagnetic torque motor is often used as the driving part, its structure is complex. Large volume weight, low frequency response, large impact, slow response speed, low resolution, low control precision and poor anti-interference ability. In addition, in many research fields, small flow rate is required to complete system control. In order to reduce the volume and weight of the system, reduce the loss of energy consumption and improve the performance of the system, but at the same time must bear the high and low pressure and high and low temperature and other special factors. In this paper, piezoelectric ceramic and metal rubber are used to design a new precise flow valve. This paper mainly studies the flow characteristics of the flow valve, the distribution of the flow field in the valve chamber and the flat ripple characteristics at the outlet of the valve. Based on Darcy's law and the conservation theorem of fluid mass, the mathematical model of valve flow characteristics is established, and the influence of metal rubber geometry parameters and valve inlet and outlet pressure difference on valve flow characteristics is analyzed by matlab software. The influence of radius of circular angle and half cone angle of valve core on the flow field characteristics and the influence of metal rubber parameters on the flat ripple characteristics of flow valve were analyzed by Fluent12.0 software. The analysis results show that the flow characteristics of the valve are not only related to the driving voltage, but also to the parameters of the metal rubber ring. The distribution of the flow field in the valve cavity is greatly affected by the radius of the circular angle and the half cone angle of the valve core. After the metal rubber ring is installed at the inlet and outlet of the valve, the fluid velocity of the outlet valve changes slowly, the direction tends to be consistent, and the flow is more smooth, which to some extent ensures the stability of the output flow / pressure of the valve. In order to achieve a certain range of flat wave processing function.
【學位授予單位】：南昌大學
【學位級別】：碩士
【學位授予年份】：2012
【分類號】：TH137.522

【參考文獻】

相關期刊論文 前8條

1 賈光政,王宣銀,吳根茂;超高壓大流量氣動開關閥的原理和動態特性研究[J];機械工程學報;2004年05期

2 侯繼偉,葉樹明,張建文,李世倫;新型微流量超高壓海水比例溢流閥的研制[J];液壓與氣動;2004年01期

3 賀小峰;王學兵;李壯云;;直動式水壓溢流閥的動態特性分析與試驗[J];機械與電子;2007年02期

4 姜洪源,敖宏瑞,夏宇宏,王樹國,呂克法,呂巖;金屬橡膠成型工藝研究及其應用[J];機械設計與制造;2001年02期

5 楊曙東,李壯云;一種高壓大流量氣動定差壓力控制閥的研究[J];機械科學與技術;2001年03期

6 陳艷秋,朱梓根;用于管路的薄金屬橡膠減振器的性能研究[J];航空動力學報;2001年02期

7 楊紅艷,房彥偉;滑閥式超高壓換向閥優化設計及動態仿真[J];機床與液壓;2003年02期

8 李中郢,盧正人;航天器用新型金屬橡膠減振器[J];上海航天;2005年05期

，

本文編號：2148820