發布時間：2018-07-29 15:45

【摘要】：工業門是工業廠房和物流倉庫的配套設施，伴隨著工業化進程的加速發展和物流倉庫現代化水平的不斷提高，工業門領域也在不斷的發展，人們對于工業門在使用功能和安全方面的要求也在不斷的增多。因此，對工業門的研究和設計具有重要的意義。 本文在廣泛閱讀文獻和調研的基礎上，根據大型廠房以及大型工業設備的需要開發設計了工業多段分節提升門。本文對工業多段分節提升門各部分設計進行了詳細的介紹，使用基于Windows開發的三維CAD系統SolidWorks軟件進行結構設計。利用有限元分析軟件ANSYS對工業多段分節提升門的主要受力部件進行有限元分析，使其滿足設計要求。本文主要有以下幾個方面的研究工作。 根據工業門技術參數和使用功能的要求，，設計了新型的工業多段分節提升門，介紹了其工作原理、產品功能以及主要部件的結構設計。本文對工業多段分節提升門的門體系統、軌道系統、平衡系統、密封系統、傳動系統以及五金配件進行了詳細的分析和設計，并使用SolidWorks軟件繪制其三維零件模型圖以及總體裝配圖。同時本文對開門電機的功率，提升鋼絲繩的直徑，滾輪軸的大小進行了詳細的計算。此外，工業多段分節提升門安裝完成之后外力主要承受風載荷的作用，因此，對門板的抗風壓性能進行了有限元分析，使之滿足抗風載荷的要求。 在原有機構的基礎上對停電處理機構進行了改進設計，設計之后的停電處理機構更加簡單可靠。 本文對平衡系統進行了分析與設計，運用理論的方法對提升扭簧的剛度、最大轉矩、最大扭轉角進行了詳細的計算，確定了提升扭簧的相關參數。此外，扭簧軸是平衡系統的關鍵部件，通過強度條件和剛度條件設計扭簧軸的直徑，并對扭簧軸進行了有限元分析，以此驗證扭簧軸設計的可行性。 本文對工業門控制系統進行了詳細的介紹，控制系統是工業多段分節提升門的核心，充分考慮了人性化的功能要求，采用PLC對工業多段分節提升門的開啟關閉程度進行精確控制，并且繪制了控制系統的流程圖。此外，對主控單元、電源單元、控制傳感器和其它電器元件進行了選型設計。 本文對其它輔助功能也作了相應的研究和設計。 在總結與展望中，本文對工業門的研究與設計提出了進一步的展望，希望后續工作中從工業門提升形式、門板材料以及控制方面對工業門進行深入的研究。
[Abstract]:Industrial door is the supporting facilities of industrial workshop and logistics warehouse. Along with the accelerated development of industrialization and the continuous improvement of modernization level of logistics warehouse, the field of industrial door is also developing continuously. People for industrial doors in the use of function and safety requirements are also increasing. Therefore, the research and design of industrial door is of great significance. On the basis of extensive reading of literature and investigation, this paper develops and designs industrial multi-segment lifting doors according to the needs of large factories and industrial equipment. In this paper, the design of industrial multi-segment lifting gate is introduced in detail, and the SolidWorks software of 3D CAD system based on Windows is used to design the structure. The finite element analysis software ANSYS is used to analyze the main force components of the industrial multi-segment lifting door, so that it can meet the design requirements. This article mainly has the following several aspects of research work. According to the requirements of technical parameters and application functions of industrial doors, a new type of industrial multi-segment lifting door is designed, and its working principle, product function and structure design of main components are introduced. In this paper, the door system, track system, balance system, sealing system, transmission system and hardware fittings of multi-segment lifting door are analyzed and designed in detail. And use SolidWorks software to draw its three-dimensional part model diagram and the overall assembly drawing. At the same time, the power of the door motor, the diameter of the wire rope and the size of the roller shaft are calculated in detail. In addition, after the installation of the multi-segment lifting door, the external force mainly bears the effect of the wind load. Therefore, the anti-wind pressure performance of the door plate is analyzed by finite element method to make it meet the requirements of the anti-wind load. On the basis of the original mechanism, the blackout treatment mechanism is improved, and the blackout treatment mechanism is more simple and reliable after the design. In this paper, the balance system is analyzed and designed, and the stiffness, maximum torque and maximum torsion angle of the lifting torsion spring are calculated in detail by using the theoretical method, and the relevant parameters of the lifting torsion spring are determined. In addition, the torsion spring shaft is the key component of the balance system. The diameter of the torsion spring shaft is designed by strength and stiffness conditions, and the finite element analysis of the torsion spring shaft is carried out to verify the feasibility of the torsion spring shaft design. In this paper, the industrial door control system is introduced in detail. The control system is the core of the industrial multi-segment lifting door. The PLC is used to accurately control the opening and closing degree of the industrial multi-segment lifting door, and the flow chart of the control system is drawn. In addition, the main control unit, power supply unit, control sensor and other electrical components are selected and designed. This article also makes the corresponding research and the design to the other auxiliary function. In the summary and prospect, this paper puts forward a further prospect for the research and design of industrial door, and hopes to further study the industrial door from the aspects of industrial door lifting form, door panel material and control in the following work.
【學位授予單位】：吉林大學
【學位級別】：碩士
【學位授予年份】：2014
【分類號】：TB472;TP273

【參考文獻】

相關期刊論文 前10條

1 楊梅;論鋁合金隔熱斷橋門窗在建筑藝術中的實用性表現[J];甘肅科技;2005年04期

2 劉佳才;現代工業門、月臺跳板的現狀與發展趨勢[J];中國儲運;2002年05期

3 蔣蕊聰;;快速發展的闊福門業[J];中國儲運;2007年10期

4 羿生鉆;;超寬自動提升門設計與施工[J];大眾科技;2009年03期

5 丁明華;;可編程控制器程序設計方法初探[J];電子技術與軟件工程;2013年22期

6 季克其;MKQ-2型無線遙控電動門控制電路[J];電子世界;2001年08期

7 譚景和,楊婷連,朱壽增,劉之葵;簡易法作內力圖[J];高教論壇;2003年05期

8 曹新勝;;提高節能門窗的綜合性能[J];建設科技;2009年03期

9 張?jiān)��?;大型鋼結構中高強度螺栓連接的布局分析及設計[J];機械設計與制造;2012年09期

10 劉佳才;物流單元周邊設備的應用及發展[J];物流技術與應用;2003年02期

本文編號：2153165