發布時間：2018-01-23 09:50

  本文關鍵詞： 渦激振動 流機電耦合 能量收集模型 計算方法 能量收集特性　出處：《重慶大學》2014年博士論文　論文類型：學位論文

【摘要】：隨著微能源、MEMS、無線傳感器網絡等技術的飛速發展，使用壓電轉換振動能量收集原理(PEH)收集流體機械能成為近年的研究熱點。壓電振動能量收集作為一種有效的環境能源收集技術，受到了國內外廣泛關注，主要應用于健康監控、無線傳感器系統、微小型電機耦合器件等領域。因此，研究壓電振動能量收集技術具有廣闊的應用前景和實用價值。渦激振動(VIV)現象可將流動能轉化為振動能。渦激振動中的鎖定效應可有效增加振動強度，從而提高能量收集的效率，具有重要研究?jī)r(jià)值。然而目前針對渦激振動能量收集技術(VIVPEH)的研究極少，特別是針對流場流動-機械振動-帶電回路(流機電)多物理場耦合模型建立和求解方法的研究鮮有報道。因此，本文針對流機電多物理場耦合渦激振動能量模型及特性的研究具有非常重要的學術意義和價值。 本文首先針對渦激振動中存在的流固耦合問題，進行了流固耦合渦激振動的數學模型建立和求解方法的研究。其次，進行了如何將渦激振動現象與壓電能量收集系統進行流機電多物理場耦合的研究，重點進行了如何建立流機電多物理場耦合數學模型以及如何對該模型進行求解的研究。然后，本文基于以上流機電多物理場耦合模型與方法，對光滑圓柱、PTC圓柱、帶攻角方柱、不同頂角三角柱等幾種不同形狀柱體VIVPEH在不同外接負載條下，不同來流速度時的振動響應、流場特性和能量收集特性進行了深入研究。得出了以下主要成果： ①首次建立了一種計算流固耦合VIV動態響應的數值計算方法，該方法可以將流體連續性方程和N-S方程與柱體振動方程同時求解，，并且可以克服傳統動網格技術的畸變和扭曲等問題。為驗證流固耦合渦激振動求解方法，首先使用靜態柱體繞流的方法，驗證了本文外流場求解數值方法在求解大范圍雷諾數時的準確性。然后，在風洞實驗中，通過測試不同來流速度下的光滑圓柱VIV振幅，與利用本文數值求解方法所得結果進行對比，驗證了本文VIV流固耦合數值求解方法的準確性。 ②基于壓電懸臂梁能量收集的集總參數模型，同時考慮鈍體的振動、外部流場的流動和壓電回路三者的相互作用，首次建立了將鈍體繞流渦激振動作為動態載荷，帶動壓電懸臂裝置進行振動并且收集渦激振動能量的數學模型，并提出了該模型的數值求解方法。首先，使用系數矩陣法，求解由機電耦合鈍體振動方程的線性形式和高斯定律組成的方程組，求得了外接負載對鈍體振動系統的負反饋?zhàn)饔茫瑥亩�消除了振�?dòng)方程中的電壓項，使得振動方程降維，從而可以使用本文的流固耦合VIV數值計算方法中進行求解，并得出振動響應和流場特性；然后使用基于正弦波的準穩態理論，求解高斯定律，得到能量收集電壓和功率輸出的一般形式。最后，將振動振幅的計算結果代入電壓輸出和功率輸出的表達式中，即可獲得流機電多物理場耦合的渦激振動能量收集特性。 ③基于流機電多物理場耦合渦激振動能量收集數學模型和求解方法，首次獲得了流機電多物理場耦合下，光滑圓柱、PTC圓柱VIVPEH在不同外接電阻對振動系統的負反饋下的渦激振動響應及能量收集特性。機電耦合阻尼會隨電阻增大而先增大后減小，而機電耦合頻率在經歷一個階躍性上升后重新達到平穩。振幅曲線中觀察到了振幅曲線中的三個分支，光滑圓柱與PTC圓柱的振幅最大值較為接近，且PTC圓柱的鎖振區域得到了延后。光滑圓柱與PTC圓柱VIVPEH的輸出電壓和功率最大值較為接近。 ④獲得了不同攻角方柱和不同頂角三角柱VIVPEH的能量收集特性，結果表明方柱VIVPEH能量收集特性要優于圓柱，而三角柱VIVPEH要優于方柱。攻角對方柱振動振幅最大值和鎖振區域有著較大影響，最大振幅、電壓、功率輸出出現在攻角為45°時。三角柱VIVPEH的能量收集能力要明顯強于圓柱和方柱，鎖振區域和電壓、功率輸出最大值均得到了提高。 ⑤在對比多種柱體VIVPEH的能量收集特性的基礎上，發現60°頂角三角柱VIVPEH的能量收集能力最強，最有利于渦激振動能量收集。60°頂角三角柱較之PTC圓柱的最大電壓提升了176.23%，最大功率提升了661.8%。
[Abstract]:With the rapid development of micro energy, MEMS, wireless sensor network technology, using the piezoelectric conversion principle of vibration energy collection (PEH) collection of fluid machinery can become a research hotspot in recent years. The piezoelectric vibration energy harvesting as an effective environmental energy harvesting technology, has attracted wide attention at home and abroad, mainly used in health monitoring. Wireless sensor system, the field of micro motor coupler. Therefore, the research of piezoelectric vibration energy harvesting technology has a wide application prospect and practical value. The vortex induced vibration (VIV) phenomenon can be transformed into vibrational energy flow. The locking effect of vortex induced vibration in vibration can effectively increase the strength, so as to improve the efficiency of energy collection and it has important research value. However, the vortex induced vibration energy harvesting technologies (VIVPEH) few studies, especially for electric circuit with flow - mechanical vibration (electromechanical flow) There are few reports on the establishment and solution methods of multi physical field coupling models. Therefore, it is of great academic significance and value to study the energy model and characteristics of multi physics field coupled vortex induced vibration.
Aiming at the existence of vortex induced vibration of the fluid solid coupling problem, studied the mathematical model of fluid solid coupling of vortex induced vibration is established and the solving method. Secondly, for how the vortex induced vibration phenomenon and the piezoelectric energy harvesting system flow research of electromechanical coupled multi physics field, focusing on how to establish flow and multi field coupling mathematical model and study how to solve the model. Then, the above flow of electromechanical coupled multi physics model and method based on smooth cylindrical, PTC cylindrical, square columns with angle of attack, different angle three prism shapes column VIVPEH in different load. The vibration response of the different flow speed, flow characteristics and energy collection characteristics were studied. The following main results:
For the first time established a calculation method for the calculation of fluid solid coupling dynamic response of VIV value, the method can make the fluid continuity equation and N-S equation and the cylinder vibration equations are solved simultaneously, and it can overcome the traditional technique of dynamic mesh distortion and distortion problems. The fluid solid coupling method for vortex induced vibration test method the first use of static column flow, verify the accuracy of the flow field numerical method in solving a wide range of Reynolds numbers. Then, during the wind tunnel experiments, through the test of different flow velocity under the smooth cylindrical VIV amplitude, the results were compared with the use of numerical methods in this paper, to verify the accuracy of the VIV a numerical method for solving the flow solid coupling.
The lumped parameter model of piezoelectric cantilever beam energy collection based on considering the vibration blunt body, interaction between external flow field and piezoelectric loop three, first established the vortex induced vibration action as dynamic load, driven by the mathematical model of piezoelectric cantilever device for vibration and vortex collection the vibration energy, and puts forward the numerical solution of the model. First, using the coefficient matrix method, equations composed of electromechanical coupling vibration equation of the linear form of the bluff body and Gauss's law, the external load feedback effect of vibration system of the bluff body is obtained, which eliminates the voltage vibration equation. So, the vibration equation of dimensionality reduction, which can be used in the numerical calculation method of fluid solid coupling in VIV is solved, and the response and flow characteristics of vibration; and then use the quasi steady state theory based on sine wave, the solution of Gauss The general form of energy collection voltage and power output is obtained. Finally, the calculation results of vibration amplitudes are substituted into the expressions of voltage output and power output, and the energy harvesting characteristics of vortex induced vibration of multi electromechanical coupling of flow and electromechanical can be obtained.
The multi field coupling vortex vibration energy collection mathematical model and solving method of electromechanical flow based on the obtained flow electrical multi physics coupling, cylindrical, cylindrical PTC VIVPEH resistor under different external vibration system of the negative feedback of the vortex induced vibration and energy harvesting characteristics of electromechanical coupling damping will begin. Increases and then decreases with the increase of resistance, and the electromechanical coupling frequency after a step up again after reaching steady. The amplitude curves were observed in the three branches of the amplitude curves, maximum amplitude and smooth cylindrical PTC cylinder is closer, and the vibration of PTC cylindrical lock region has been delayed. The output voltage and the maximum power of PTC and VIVPEH of the cylindrical cylinder is close to.
The obtained energy collection characteristics at different angles of square column and different angle triangular VIVPEH, results show that VIVPEH is superior to the characteristics of energy collection column column, and the triangular column of VIVPEH is better than that of the square column. Had a great influence on other column vibration amplitude maximum angle of attack and lock vibration area, the large amplitude, voltage, power output the attack angle is 45 degree. The energy harvesting capability of triangular VIVPEH is better than the circular and square column, lock vibration region and voltage, the maximum power output are improved.
Based on the characteristics of energy collection and comparison of a variety of column VIVPEH, found that 60 degree angle triangular VIVPEH energy harvesting ability is the strongest, most conducive to the vortex induced vibration energy collection maximum voltage.60 DEG angle triangular column than PTC columns increased by 176.23%, the maximum power increased by 661.8%.

【學位授予單位】：重慶大學
【學位級別】：博士
【學位授予年份】：2014
【分類號】：TB535

【參考文獻】

相關期刊論文 前10條

1 劉祥建;陳仁文;;壓電振動能量收集裝置研究現狀及發展趨勢[J];振動與沖擊;2012年16期

2 陳定方;孫科;李立杰;楊艷芳;梅杰;;微型壓電能量收集器的研究現狀和發展趨勢[J];湖北工業大學學報;2012年04期

3 羅承先;;世界風力發電現狀與前景預測[J];中外能源;2012年03期

4 李軍軍;吳政球;譚勛瓊;陳波;;風力發電及其技術發展綜述[J];電力建設;2011年08期

5 李泓澤;郭森;王寶;;我國風力發電的環境價值分析[J];能源技術經濟;2011年07期

6 鮮榮;廖海黎;李明水;;大比例主梁節段模型渦激振動風洞試驗分析[J];實驗流體力學;2009年04期

7 詹昊;方秦漢;李萬平;;鋼桁拱橋吊桿渦激振動仿真分析[J];中國鐵道科學;2009年02期

8 徐楓;歐進萍;肖儀清;;方柱流致橫向振動的CFD數值模擬[J];哈爾濱工業大學學報;2008年12期

9 李寧;程禮;;壓電分流阻尼的虛擬實現[J];空軍工程大學學報(自然科學版);2008年04期

10 賀學鋒;溫志渝;溫中泉;尚正國;劉海濤;廖海洋;;振動式壓電發電機的理論模型與實驗[J];納米技術與精密工程;2007年04期

相關博士學位論文 前2條

1 丁林;被動湍流控制下多柱體流致振動研究[D];重慶大學;2013年

2 徐楓;結構流固耦合振動與流動控制的數值模擬[D];哈爾濱工業大學;2009年

本文編號：1457270