發布時間：2018-02-22 21:53

  本文關鍵詞： 永磁同步平面電機 水冷散熱系統 水冷散熱器 CFD　出處：《電子科技大學》2015年碩士論文　論文類型：學位論文

【摘要】：隨著科技的不斷進步,高新技術制造業向著高速化、精密化和模塊化方向發展,對制造領域內加工設備的定位精度和速度提出了嚴格的要求。平面電機具有結構簡單、反應迅速、靈敏度高等特點,使其在平面二維定位裝置上廣泛應用。但是平面電機的發熱功率較高,熱流密度較大,為保障其正常運行和控制精度,就必須對電機進行散熱研究。傳統的散熱方式風冷,已經逐漸不能滿足這種高熱流密度的要求,而水冷散熱器因為其高對流換熱系數和高效率被廣泛地研究�；�于此,本文針對一種動圈式永磁同步平面電機設計并制作了一套水冷散熱系統。針對散熱系統的核心部件水冷散熱器進行研究,對于散熱器的設計和提高散熱器的性能具有重要意義,對于加強平面電機的溫度均勻性具有實際意義。本文首先針對水冷散熱器進行研究,基于對傳統流道結構水冷散熱器性能的研究,即傳統串聯流道結構水冷散熱器散熱效率高而流道內壓力損失較大,對泵的要求較高,而傳統并聯水冷散熱器流道壓力損失較低,不過其散熱效率也較低且通道內水的流速不均勻。根據文獻的調研及科研經驗,總結了如何提高散熱器性能的方法,因此為了提高散熱器的性能,增強散熱器的均溫性,本文在此基礎上提出了其他三種新型的流道結構的水冷散熱器,即串并聯流道結構、雙串聯流道結構和螺旋型流道結構。為了驗證各種散熱器的性能,通過運用仿真軟件ANSYS Workbench對不同流道結構散熱器進行CFD仿真分析。通過仿真可以得到散熱器溫度分布及散熱器內流場分布,據此分析比較各散熱器的性能,可以發現新型散熱器綜合性能比傳統散熱器要好,而均溫性最好的是螺旋型流道結構散熱器。最后,將綜合性能較好且均溫性最好的螺旋型流道結構散熱器應用在實際的平面電機上,首先仿真分析散熱器的在平面電機上的應用情況,然后設計并完成一套實驗測試平臺的搭建,研究螺旋型散熱器的散熱效率,實驗獲得了散熱器在不同進口流速下的流動特性與散熱性能,驗證了本文提出的水冷散熱系統的可行性。最終,對比分析了實驗結果與仿真分析結果,兩種結果保持了較好的吻合趨勢,即驗證了數值研究的合理性,又為水冷散熱器在平面電機的應用提供了實驗依據。
[Abstract]:With the continuous progress of science and technology, the high-tech manufacturing industry is developing towards high speed, precision and modularization, which puts forward strict requirements for the positioning accuracy and speed of machining equipment in the manufacturing field. Due to its rapid reaction and high sensitivity, it is widely used in planar two-dimensional positioning device. However, the plane motor has high heating power and high heat flux, so it can guarantee its normal operation and control accuracy. It is necessary to study the heat dissipation of the motor. The traditional cooling method of air cooling has been unable to meet the requirement of this kind of high heat flux, while the water cooling radiator has been widely studied because of its high convection heat transfer coefficient and high efficiency. In this paper, a set of water-cooled heat dissipation system is designed and manufactured for a moving coil permanent magnet synchronous plane motor. The research on the water cooling radiator, which is the core part of the cooling system, is of great significance to the design of the radiator and the improvement of the performance of the radiator. It is of practical significance to strengthen the temperature uniformity of planar motor. Firstly, this paper focuses on the research of water-cooled radiator, based on the study of the performance of traditional flow channel structure water-cooled radiator. That is, the traditional water-cooled radiator with series flow channel structure has high efficiency and high pressure loss in the flow channel, and requires higher pump, while the pressure loss of the flow channel of the traditional parallel water-cooled radiator is lower. However, the efficiency of heat dissipation is also low and the flow rate of water in the channel is not uniform. According to the literature investigation and scientific research experience, the method of how to improve the performance of radiator is summarized, so in order to improve the performance of radiator and enhance the uniform temperature of radiator, On the basis of this, three other kinds of water-cooled radiators with new flow channel structure, namely series-parallel flow channel structure, double series flow channel structure and spiral flow channel structure, are proposed to verify the performance of various radiators. By using the simulation software ANSYS Workbench to simulate the radiators with different flow channels, the temperature distribution and the flow field distribution in the radiators can be obtained, and the performance of the radiators is analyzed and compared. It can be found that the new type of radiator has better comprehensive performance than the traditional radiator, and the heatsink with the best average temperature is the spiral flow channel structure radiator. The spiral flow channel radiator with better comprehensive performance and the best average temperature is applied to the actual plane motor. Firstly, the application of the radiator in the plane motor is simulated and analyzed, and then a set of experimental test platform is designed and completed. The heat dissipation efficiency of the spiral radiator is studied. The flow characteristics and heat dissipation performance of the radiator at different inlet velocity are obtained experimentally, and the feasibility of the water-cooled heat dissipation system proposed in this paper is verified. The experimental results and the simulation results are compared and analyzed. The two results are in good agreement with each other, which verifies the rationality of the numerical research and provides the experimental basis for the application of the water-cooled radiator in the plane motor.
【學位授予單位】：電子科技大學
【學位級別】：碩士
【學位授予年份】：2015
【分類號】：TM341

【參考文獻】

相關期刊論文 前1條

1 徐國強;王夢;陶智;吳宏;;矩形通道中亞尺度肋片的流動換熱數值分析[J];北京航空航天大學學報;2007年11期

，

本文編號：1525400