發布時間：2018-05-03 23:28

  本文選題：導熱性能 + 復合材料　； 參考：《青島科技大學》2017年碩士論文

【摘要】：由于科技的飛速發展,復合材料的導熱得到了廣泛的應用,尤其填充型復合材料已經成為了廣大學者們的研究熱點。本文通過DIGIMAT軟件得到了碳纖維填料及二元混合填充橡膠復合材料的代表體積單元模型,并通過有限元分析軟件ANSYS對復合材料模型的導熱性能進行數值模擬計算。主要討論了碳纖維填充量、填充個數、長徑比、彎曲度對復合材料導熱性能的影響;二元混合填料填充順序、填充配比及其中一種含量變化時對復合材料導熱性能的影響。研究表明:在不同填料添加復合材料時,由于碳纖維有明顯的各向異性,填料空間分布對復合材料導熱性能的影響較為明顯。碳纖維填充根數變化時復合材料熱導率的變化微乎其微,復合材料熱導率隨著碳纖維填充分?jǐn)?shù)的增大而增大,數值模擬結果與理論結果及實驗結果的變化趨勢一致;當碳纖維含量一定時,增大碳纖維的長徑比能更好的提高復合材料的熱導率。對于直形碳纖維,定向填充復合材料時的熱導率最大。在復合材料中添加彎曲碳纖維時,其熱導率隨著彎曲度的增大先增大后減小。當彎曲碳纖維長徑比變化時,擬合得到了不同區段長徑比與復合材料導熱性能的關系,利用擬合公式可以更好的預測不同長徑比下復合材料的熱導率。二元混合添加的復合材料,兩種填料的添加順序?qū)��?fù)合材料導熱性有一定的影響,先添加碳纖維時復合材料的熱導率較高;兩種填料在不同配比下,碳纖維對復合材料熱導率起主導作用,隨著碳纖維配比的增大,復合材料導熱性隨之增大;其中一種添加物含量一定時,復合材料熱導率伴隨另一種添加物含量的增加而增大。除了討論碳纖維,還探討了碳納米管添加復合材料的熱導率,將多壁碳納米管等效為圓柱體。碳納米管彎曲度增大,復合材料熱導率下降;增加碳納米管直徑提高其填充量,復合材料熱導率呈現出線性增大的趨勢。
[Abstract]:Due to the rapid development of science and technology, the heat conduction of composite materials has been widely used, especially the filled composite materials have become the research hotspot of the majority of scholars. In this paper, the representative volume element model of carbon fiber filler and binary mixed filled rubber composite is obtained by DIGIMAT software, and the thermal conductivity of the composite model is simulated by finite element analysis software ANSYS. The effects of carbon fiber filling amount, filling number, aspect ratio, bending degree on the thermal conductivity of composites were discussed, and the effects of filling sequence, filling ratio and one of them on the thermal conductivity of composites were discussed. The results show that the space distribution of carbon fiber has obvious influence on the thermal conductivity of the composites due to the obvious anisotropy of carbon fiber when the composites are added with different fillers. The thermal conductivity of the composite increases with the increase of the carbon fiber filling fraction, and the numerical simulation results are consistent with the theoretical and experimental results. When the content of carbon fiber is constant, increasing the aspect ratio of carbon fiber can improve the thermal conductivity of composites better. For straight carbon fiber, the maximum thermal conductivity is obtained when the composite is filled in directionally. When the bending carbon fiber is added into the composite, the thermal conductivity increases first and then decreases with the increase of the bending degree. When the ratio of length to diameter of bending carbon fiber changes, the relationship between the ratio of length to diameter and the thermal conductivity of composites in different regions is obtained, and the thermal conductivity of composites under different ratio of length to diameter can be better predicted by using the fitting formula. The addition order of two fillers has a certain influence on the thermal conductivity of the composites, and the thermal conductivity of the composites is higher when carbon fiber is added first, and the thermal conductivity of the composites is higher when the two kinds of fillers are added in different proportions. Carbon fiber plays a leading role in the thermal conductivity of composites, and the thermal conductivity of composites increases with the increase of carbon fiber ratio, and the thermal conductivity of the composites increases with the increase of the content of the other additives when the content of one additive is constant. In addition to carbon fiber, the thermal conductivity of carbon nanotubes (CNTs) added into composites is also discussed, and the multi-walled CNTs are equivalent to cylinders. The thermal conductivity of the composites decreases with the increase of the bending degree of carbon nanotubes, and the increase of the diameter of carbon nanotubes with the increase of the filling amount, the thermal conductivity of the composites increases linearly.
【學位授予單位】：青島科技大學
【學位級別】：碩士
【學位授予年份】：2017
【分類號】：TB332

【參考文獻】

相關期刊論文 前10條

1 張先偉;范宏;;填充型導熱硅橡膠研究進展[J];化學反應工程與工藝;2015年06期

2 何和智;吳明春;周麗英;;AlN填充PA6導熱復合材料的性能研究[J];塑料工業;2015年09期

3 何達;謝林生;馬玉錄;;聚偏氟乙烯/鱗片石墨/碳纖維高導熱復合材料的制備[J];中國塑料;2015年08期

4 柏鵬光;張煥;李葉;白利忠;張志毅;劉亞青;;碳纖維/膨脹石墨協同復合對天然橡膠導熱性能的影響[J];中國膠粘劑;2015年05期

5 秘彤;盧詠來;路樹萍;于海濤;張立群;;碳納米管/炭黑/天然橡膠復合材料的性能研究[J];橡膠工業;2015年04期

6 秘彤;盧詠來;路樹萍;于海濤;張立群;;碳納米管/天然橡膠復合材料的性能研究[J];橡膠工業;2015年03期

7 張碩;程俊梅;趙樹高;;瀝青基短切碳纖維氧化改性及其天然橡膠復合材料的性能[J];合成橡膠工業;2015年02期

8 麥偉宗;王飛;黃李勝;李景;許燈波;;導熱PA6復合材料導熱性能的研究[J];合成材料老化與應用;2013年05期

9 劉海龍;王家俊;吳玲玲;姚金松;;改性氧化石墨烯/聚碳酸亞丙酯復合材料的制備及性能研究[J];浙江理工大學學報;2013年04期

10 闕玉龍;華小珍;鄒愛華;崔霞;;不同顆粒含量SiC_p/Al復合材料導熱性能的有限元分析[J];南昌航空大學學報(自然科學版);2013年02期

相關碩士學位論文 前3條

1 樓熹辰;碳纖維/高分子復合材料導熱性能研究[D];清華大學;2013年

2 胡新利;尼龍12和環氧樹脂導熱復合材料的制備及性能研究[D];上海交通大學;2013年

3 侯金星;氮化鋁/環氧樹脂復合材料的導熱與絕緣性能[D];華中科技大學;2013年

，

本文編號：1840580